The only problem with it, is that, it reload the latest driver when you plug the device on a never used USB port. So, if you change place of connection, you should manually set the driver to 3.3, but you have to do that only the first time you used this port. Next time, the driver remain to 3.3 and never upgrade to 3.6.

Download Olimex Port Devices Driver Windows 7

Overview¶

Zephyr applications use the olimex_stm32_e407 board configurationto run on the OLIMEX-STM32-E407 open source hardware. It is based onthe STMicroelectronics STM32F407ZG ARM Cortex-M4 CPU.

Now you have two different entries and interfaces associated with ARM-USB-OCD-H - one for the programming via JTAG; the other the serial port that we just installed. The above was tested on Windows 10 x64. I also tested whether the serial port and the JTAG interfaces worked properly after the driver installation. Best regards, Lub/OLIMEX. Connect the programmer to the USB and with a sharp object (needle or pin) press the upgrade pin - it is in a small hole at the back of the board (this will start the bootloader and will turn off the LED, it will also probably show a new unrecognized device in the device manager for which we will install drivers in step 3) Download and install. Download the latest drivers, software, firmware, and diagnostics for your HP products from the official HP Support website. Welcome to the NETGEAR Download Center!! To find documentation, firmware, software, or other files, enter a whole or partial Model number in the text search box.

Download olimex port devices driver download

Hardware¶

Information about the board can be found at theOLIMEX-STM32-E407 website and OLIMEX-STM32-E407 user manual.The ST STM32F407ZG Datasheet contains the processor’sinformation and the datasheet.

Supported Features¶

The olimex_stm32_e407 board configuration supports the followinghardware features:

Interface	Controller	Driver/Component
NVIC	on-chip	nested vectoredinterrupt controller
SYSTICK	on-chip	system clock
UART	on-chip	serial port
GPIO	on-chip	gpio

Other hardware features are not supported by the Zephyr kernel.

Pegatron laptops & desktops driver download for windows 7. Pegatron laptops Operating System Versions: Windows XP, 7, 8, 8.1, 10 (x64, x86).

Pin Mapping¶

LED¶

LED (green) = PC13
PWR_LED (red) = power

External Connectors¶

JTAG/SWD debug

PIN #	Signal Name	Pin #	Signal Name
1	+3.3V	11
2	+3.3V	12	GND
3	PB4 / TRST	13	PB3 / TDO
4	GND	14	GND
5	PA15 / TDI	15	PB4 / TRST
6	GND	16	GND
7	PA13 / TMS	17
8	GND	18	GND
9	PA14 / TCK	19	+5V_JTAG
10	GND	20	GND

UEXT

PIN #	Wire Name	STM32F407 port
1	+3.3V
2	GND
3	PC6/USART6_TX	PC6
4	PC7/USART6_RX	PC7
5	PB8/I2C1_SCL	PB8
6	PB9/I2C1_SDA	PB9
7	PC2/SPI2_MISO	PC2
8	PC3/SPI2_MOSI	PC3
9	PB10/SPI_SCK/UART3_TX	PB10
10	RB7/UEXT_CS	PB7

Arduino Headers¶

CON1 power

Pin	Signal Name	STM32F407 Pin#
RST	RESET	25
3V3	VCC (3V3)	N/A
5V	VDD (5V)	N/A
GND	GND	N/A
GND	GND	N/A
VIN	VIN	N/A

CON2 analog

Pin	Signal Name	STM32F407 Pin#
A0	PC0	26
A1	PF6	18
A2	PF7	19
A3	PF8	20
A4	PF9	21
A5	PF10	22

CON3 digital

Pin	Signal Name	STM32F407 Pin#
D0	PB7/USART1_RX	137
D1	PB6/USART1_TX	136
D2	PE2	1
D3	PE4	3
D4	PE5	4
D5	PR6	5
D6	PG7	92
D7	PG8	93

CON4 digital

Pin	Signal Name	STM32F407 Pin#
D8	PG12	35
D9	PG15	70
D10	PA4	40
D11	PB5	43
D12	PA6	42
D13	PA5	41
GND	AGND	31
AREF	AREF	32

PIN #	Signal Name	Pin #	Signal Name
1	+3.3V	11	PD8
2	GND	12	PD9
3	PD0	13	PD10
4	PD1	14	PD11
5	PD2/SD_MMC	15	PD12
6	PD3	16	PD13
7	PD4	17	PD14
8	PD5	18	PD15
9	PD6	19	+5V
10	PD7	20	GND

PIN #	Signal Name	Pin #	Signal Name
1	+3.3V	11	PE8
2	GND	12	PE9
3	PE0	13	PE10
4	PE1	14	PE11
5	PE2/D2	15	PE12
6	PE3	16	PE13
7	PE4/D3	17	PE14
8	PE5/D4	18	PE15
9	PE6/D5	19	+5V
10	PE7	20	GND

PIN #	Signal Name	Pin #	Signal Name
1	+3.3V	11	PF8/A3
2	GND	12	PF9/A4
3	PF0	13	PF10/A5
4	PF1	14	PF11/A6
5	PF2	15	PF12
6	PF3	16	PF13
7	PF4	17	PF14
8	PF5	18	PF15
9	PF6/A1	19	+5V